Use the eye bolt that is stamped with its rated weight. Do not shock load eye bolts. Regular eye bolts have a working load limit which should be taken into consideration when used Compare.

An eye bolt is a bolt with a loop at one end.

Frequently a nut is attached to the bottom for additional safety. The advantage to them over eye bolts is that they maintain 100 percent of the working load These fittings have Eye bolts without a shoulder should not be used for angular loads.

Therefore, all of the holding strength of the machinery eye bolt is on the threads. First, determine thickness of what the eye bolt will be going through.Then, choose an eye bolt with a shank long enough so that the threads protrude on the back side and allow the nut to be tightened properly.If the unthreaded portion of the shank protrudes below the bottom surface and does not allow the nut to be tightened, you can use washers to fill the space of the unthreaded portion of the shank.

Never use an eye bolt that shoes signs of wear or damage. They are simple pieces of hardware. Do not paint an eye bolt. be lifted. This absorbs shock loads if the chain suddenly gets yanked up tight. At 0 to 5 degrees, the eye bolt is rated at 100 percent of its working load limit. For example: A lag eye bolt will hold more load when screwed into a new oak board, compared to an old pine fence post. Hardware Essentials 1/2-13 x 8 in. a shoulder allowing for lifting at slight angles, and a listed working load limit.

The lifting eyebolt is designed for lifting wooden or steel components. Instructions for assembly. Limits of use. These fittings are very versatile and are designed to be inserted through a hole and secured on the back side


In these circumstances, the lifting eye bolt should include a shoulder to prevent the shank from bending. How should you use eye bolts safely?

Where angled lifts cannot be avoided you should discuss the correct load capacity with the supplier. Free delivery with $45 order. Like wire eye bolts, wire eye lags are intended for light duty applications and should not be used for angular loads. for lifting or supporting an overhead load. The 75% reduction in capacity makes the effective working load limit only 388 lbs. Machinery eye bolts are designed with a shoulder and are designed for angular loading. Type a word, a phrase, or ask a question At 45⁰ the actual capacity 30% of its weighted working load.A rated eye bolt has been independently tested and certified as compliant with industry standards for performance and mechanical strength. Eye bolts made by bending a rod or wire into a loop are only suitable for light duty applications, as heavy loads can cause the eye to open. The lifting eyebolt is designed for lifting wooden or … They are simple pieces of hardware. The difference between machinery eye bolts and regular and shoulder type eye bolts is that the shank and threads of the machinery eye bolt do not protrude through the base metal. A longer shank length allows you to go through thicker objects. The eye bolt must be aligned during installation and tightened to secure it against rotation during lifting.

The steeper the angle the lower the load capacity. Regular Nut Eye Bolt Shoulder Nut Eye Bolt Machinery Eye Bolt G-291 G-277 G-279 Important Safety Information— Read and Follow Inspection/Maintenance Safety: † Always inspect eye bolt before use. Shoulder eye bolts have a supporting shoulder that allows them to be loaded at slight angles, if properly installed. Note that all the eye bolts are NOT “in line.”To correct this, we are going to add washers as needed to get the eye bolts into the “in line” position as shown here.

Do not force hooks or other fittings into the eye; they must fit freely. An eye bolt is one of the most commonly used tools in the material handling toolbox.They are simple pieces of hardware.

In this case, the catalog working load limit of this 3/8th inch eye bolt is 1,550 pounds.At 15 degrees, the working load limit is reduced by 20% and the effective working load limit of the eye bolt becomes 1240 pounds, which is 80% of the original rated capacity.30 degrees makes for 65% of the original rated capacity.45 degrees makes for 30% of the original rated capacity.90 degrees makes for 25 % of the original rated capacity. consideration the working load limit of the object to which you are fastening the eye bolt to as this will effect the working load limit of your entire rigging assembly. Do not use bars, grips or wrenches to tighten eye bolts.

They have short, fully threaded shanks that are designed to be screwed directly into threaded or tapped holes. How to Choose and Use an Eye Bolt.

The threaded portion varies for each eye bolt, so visit our website if you need more detailed They have short, fully threaded shanks that are designed to be screwed directly into threaded or tapped holes.

INSTRUCTIONS ACCORDING TO STANDARDS DIN 580:2018 AND DIN 582:2018 . A regular nut eye bolt which is also called a plain pattern eye bolt can be used in most jobs apart from angular loads because they tend to bend. hold more load when screwed into a new oak board, compared to an old pine fence post.

For environments below -1°C the standard is ASTM F541-12.

If the load is applied sideways, the eye bolt may bend. They should never be loaded perpendicular to that axis because they are likely to bend and break.The degree of angle of your load can have a big effect on the working load limit of the eye bolt.This cable is at 0 degrees. Make sure you select the correct eyebolt based on its type and capacity for the lift you are conducting.Add a badge to your website or intranet so your workers can quickly find answers to their health and safety questions.Although every effort is made to ensure the accuracy, currency and completeness of the information, CCOHS does not guarantee, warrant, represent